Are facing low water pressure in your house? Before buying an expensive pump read this guide how to increase water pressure without a pump.
From time to time, the pressure of the water in your premise will usually go down. If and when this happens, you will highly unlikely to undertake your chores normally. Definitely, you will become greatly inconvenienced. The only way to counter this is to put in measures which are designed to increase the pressure. We have devoted this first article to just that.
- How do you increase the water pressure in your house?
- How do I increase water pressure upstairs?
- How can you fix low water pressure?
- Why do I have no water pressure all of a sudden?
How do you increase the water pressure in your house?
Clear your Pipes
The most obvious reason why water pressure falls off is clogged water pipes. It hence follows that your first step is to clear the pipes of any debris. In particular, look out for mineral residues, dirt buildups, and limestone deposits.
Check your Water Heater
Now proceed to check your water heater. While at it, determine whether the pressure of water in the heater is only low when using hot water or not. If this is the case, that could signal a fault in the water heater.
Turn your Meter Valve
Sometimes, you may accidentally turn off the water meter valve. This, of course, impedes the smooth flow of water in your plumbing system. Scan your valve to be sure that it is indeed on. Go ahead and fix it.
Block any Leakages
For water to flow smoothly and of high pressure, the entire plumbing system has to be fully functional. You should, therefore, check out for any leakages in the plumbing mechanism. To do this, turn all your faucets off. If your meter gauge is still active, that could signal a leakage.
Install a Water Pressure Booster
You may also think of installing a water booster to up the rate of water flow. This works by supplying extra ‘push’ by use of a water pump. In the course of working, it also prolongs the lifespan of your water pipes.
Contact your Water Supplier
If all the above options fail to yield the desired ends, it may be wise of you to contact a water supplier. This should also be the case of the water issue persists for too long a duration of time.
How do I increase water pressure upstairs?
Step I: Turn off all the water faucets
Kick off the exercise by turning off all the water faucets in your home. These should also apply to the sprinklers, showers, sinks, washing machines, and dishwashers. The aim is to free up your plumbing’s water pressure.
Step II: Test your Plumbing Mechanism
Having turned off all the water faucets and plumbing equipment, move on to test the plumbing mechanism. You are advised to run the shower upstairs. Take note of its performance. If it is satisfactory, then there is nothing wrong with your water pressure.
Step III: Pinpoint the water pressure regulator
In case however the performance is poor, you have to increase the water pressure in your home. To do this, pinpoint the location of the water pressure regulator. It is found in the main water line most of the time.
Step IV: Loosen the valve at the top of the valve
Move on to loosen the nut which is found at the top of your valve. Use some adjustable pliers to do so. By doing so, you get to loosen the hold of the adjustment screw which is atop the nut. It is this which lets you adjust the pressure appropriately.
Step V: Increase the Water Pressure
With the valve loosened, you may now go ahead to increase the water pressure. Turn the adjustment screw in a clockwise direction. This way, you increase the pressure of water to your entire plumbing system. Perform the shower test from time to time to gauge the performance.
Step VI: Seal the water pressure
Vary the pressure levels periodically until you arrive at a standard that is comfortable for you. After you have attained this, move on to seal it. Tighten the nut which is on the pressure valve to make this a reality.
How can you fix low water pressure?
A number of ways and means do exist. However, the following have been proven to be the most reliable:
Install a Water Booster
By far the most reliable way of doing so is to install a water booster. This is basically a special pump which increases the flow of water. Insist only on that which is powerful enough to impact your home’s plumbing system effectively.
Elevate the Main Water Supply Tank
Each home has a main water supply tank. You may consider elevating yours to increase the pressure. Mount it on a higher level and let gravity help with the pressurization of the water flow. This is also a good way of saving power.
Fix any Leaks in the System
From time to time, the plumbing system is prone to sustain some leaks. If you are affected by the menace, spare some time to fix it. You have to scan the entire plumbing to identify this issue. Some external help may be necessary.
Alter your Time of Use
The municipal water pressure is generally lower early morning and late in the evening. The reason here is that many people use water at that time. You might hence consider altering your preferred time of use to mitigate this issue.
Petition your Municipality
Lastly, you might also want to petition your municipality or local authority. Some issues like the geographical elevation of your property, the distance between your home to the nearest pump and the exact location of your home cannot be handled on your own.
Why do I have no water pressure all of a sudden?
Increase in the Number of Users
It could be that your locality has witnessed a spike in the number of users. With many users comes the need to share the water. This definitely leads to a reduction in the pressure of water. It may be solved by simultaneously upping the water supply.
Reduced Municipal Supplies
Chances are that your municipality has reduced the supply of water to your neighborhood. A number of reasons are to explain this. From the reduced levels of precipitation to government policy to non-payment of water bills. Installing a water booster may offset this issue.
From time to time, the natural sources of water may get depleted. If and when this happens, the available scarce water may have to be rationed. It is during this process of water rationing that the pressure also reduces significantly.
Leakages in the Infrastructure
For the right pressure of water to be maintained, the entire infrastructure has to be intact. Any leakages or failure in the system definitely complicates issues. It hence follows that any leakages in your plumbing or municipal pipes may cause the pressure levels to drop.
Power Supply Problems
Finally, water requires power to maintain the given pressure levels in the pipes. Any slowdown in the power supply may hence impact the pressure levels. This is an issue that is definitely beyond your scope as a homeowner. Only by contacting your municipal water supply department that you may receive the necessary help.
You have truly received the insight you require to take the right step. What more do you expect of us? Go ahead and implement the right strategy for the job. In case you are stuck, you may refer to us for further guidance.